Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

关于平面激波在凹两段楔面上的传播

众所周知,当一平面激波同任意形状的障碍物相互作用时,将产生十分复杂的波系,其中激波在曲面壁上的绕射和反射,将产生非定常波系。关于平面激波在凹圆柱壁面上的传播,我们可以用一连串、长度为无限小的楔面所构成的多边形来近似和代替凹圆柱面,因此分析和研究激波在两段楔面上反射和绕射的目的在于得出激波在圆柱壁面以及其它较复杂形状壁面上的传播规律。本文采用马赫-曾德干涉仪在激波管上进行光测模型实验。根据所拍摄的流场干涉图像,以分析其波系的演变过程及传播规律,得到有关流场的密度分布和压力分布,更为重要的是给出流场参数的定量结果。     

含有任意多个椭圆孔弹性板的应力场计算

本文应用弹性力学的复变函数理论,用多保角变换的方法,导出了含有任意多个椭圆孔的无限大弹性板多复变量应力函数的表达式。每个孔的大小、位置和孔边作用的载荷均为任意指定。板的无限远处作用有和坐标轴方向一致的均匀拉压载荷P_x,P_y和均匀剪切载荷P_(xy)。并在孔边进行复Fourier级数展开,用待定系数法确定应力函数的未知系数,从而计算弹性板的应力场。编制了相应的FORTRAN77标准化程序,进行了考题和算例分析,给出了级数的收敛状况和孔边周向应力的分布图。     

Measuring the matter distribution within z = 0.2 cluster lenses with XMM-Newton

We present an analysis of seven clusters observed by XMM-Newton as part of our survey of 17 most X-ray luminous clusters of galaxies at z  0.2 selected for a comprehensive and unbiased study of the mass distribution in massive clusters. Using the public software FTOOLS and XMMSAS we have set up an automated pipeline to reduce the EPIC MOS and pn spectro-imaging data, optimized for extended sources analysis. We also developped a code to perform intensive spectral and imaging analysis particularly focussing on proper background estimate and removal. XMM-Newton deep spectro-imaging of these clusters allowed us to fit a standard β-model to their gas emission profiles as well as a standard MEKAL emission model to their extracted spectra, and test their inferred characteristics against already calibrated relations.     

多点压力扫描阀测量系统在激波／湍流边界层干扰实验中的应用

多点压力测量是航空气动力研究及高性能流体机械研究中的重要测试手段。利用计算机和多点压力扫描阀系统，可以高效地完成这项任务，并可能在实验中实现数据采集及整个实验过程的自动化。我们利用ＨＰ１０００／Ａ７００计算机－ＨＰ２２５０－测控装置－压力传感器－高速扫描阀组成的测量控制系统，在超音速风洞内对激波／湍流边界层干扰产生的流场进行了快速多点压力数据采集，并取得了可靠的结果。本文对测试和校正过程中的程序设计、测试方法和应用经验进行了介绍。     

EFFECT OF THE RIBLETS SURFACE ON THE BOUNDARY LAYER DEVELOPMENT

ＥＦＦＥＣＴ　ＯＦ　ＴＨＥ　ＲＩＢＬＥＴＳ　ＳＵＲＦＡＣＥ　ＯＮ　ＴＨＥ　ＢＯＵＮＤＡＲＹ　ＬＡＹＥＲ　ＤＥＶＥＬＯＰＭＥＮＴＷａｎｇＪｉｎｊｕｎ；ＬａｎＳｈｉｌｏｎｇ；ＬｉａｎＱｉｘｉａｎｇ（ＩｎｓｔｉｔｕｔｅｏｆＦｌｕｉｄＭｅｃｈａｎｉｃｓＩＢｅ...     

阻尼材料在飞机炮振减振上的应用

阻尼材料在飞机结构上的应用是一个新课题。在飞机炮舱区应用新型阻尼材料,组成一个全新的阻尼结构系统来吸收由航炮射击时产生的冲击能量,以实现减振的设计目的,进而改善其炮击的振动环境。通过理论计算和地面试验实测,证明了应用新型阻尼材料可使炮舱区的动应力下降近30％。     

CFG桩复合地基应力比数值分析

本文采用有限元ANSYS程序对CFG桩复合地基的单桩桩体荷载传递规律、应力比及影响因素进行了分析,得出了减小应力比的方法和措施,对工程可起借鉴的作用。     

悬筐式蒸发器的结构设计

本文从设计角度对悬筐式蒸发器的结构进行了介绍和总结,并提出了一些结构的改进意见。